DOUBLE CUTTER-click to enlarge
click to enlarge zoom

DOUBLE CUTTER

Mat.-No.: ST-124

Double-acting hand cutter for both cutting and
notching. Supplied with a set of cutting knives and
punch-die system for 8mm notches, suitable for work
with rule of 1.42 and 2.13 mm thickness (4 and 6 pt.)
stop holder rod and telescopic stops for exact control of
workpiece dimensions.
 




NOTCHING MACHINE-click to enlarge
click to enlarge zoom

NOTCHING MACHINE

Mat.-No.: ST-124

Double-acting hand cutter for both cutting and
notching. Supplied with a set of cutting knives and
punch-die system for 8mm notches, suitable for work
with rule of 1.42 and 2.13 mm thickness (4 and 6 pt.)
stop holder rod and telescopic stops for exact control of
workpiece dimensions.
 




NICKING SHEAR-click to enlarge
click to enlarge zoom

NICKING SHEAR

Mat-No.: ST-118


Hand shear specially designed for NICKING of
cutting rule. The double angle of the punch permits
simultaneous nicking on both sides of the cut.
The punch, made of hardened ground steel, has a
thickness of 4 mm and an angle of 25°.




HAND IMPACT BENDER + SET OF ACCESSORIES-click to enlarge
click to enlarge zoom

HAND IMPACT BENDER + SET OF ACCESSORIES

Mat-No.: ST-129


Manual impact hammer bender for work with
hardened steel rule up to 30mm in height. Supplied
with telescopic measuring stop, pressure adjustment
screw and component holder adaptable to shaped
components (male and female) and cylindrical
components. Complete set of accessories comprising
sets of shaped components (male and female), one
V-shaped FEMALE component and 14 CYLINDRICAL
components of various diameters.






CREASING-MATRIX DIE CUTTER-click to enlarge
click to enlarge zoom

CREASING-MATRIX DIE CUTTER

Mat-No.: ST-119


Hand-operated machine, specially designed to cut
CREASE MATRIX strips.
The special configuration of the punch permits cutting
at a 90° angle so the strips will fit perfectly when
assembled. The stop and millimetric rule permit
pieces to be cut to the same dimensions, quickly and
accurately.






NOVA BENDER-click to enlarge
click to enlarge zoom

NOVA BENDER

Unique adjustment system means that the handle movement is the same for any bend required.  
  • The end of stroke position of the handle is easily adjusted to suit the individual. Large mechanical advantage means that rule up to 6pt (2mm) soft can be accommodated.
  • Slim dies supported overhead, mean that tight and multiple bends can be produced without complications.
  • Large bending table give maximum support to the rule.
  • Rules up to 50mm high bend in one stroke.
  • Dies slip in and out in a moment with a magnetic look holding them in position. Simple easily adjusted gauge with fine screw movement for final positioning. 
  • Provision is made for fitting to either left or right hand side of machine.
NOVA LIPPER-click to enlarge
click to enlarge zoom

NOVA LIPPER

Unique handle adjustment for comfort and maximum efficiency. Large mechanical advantage enables 2pt and 3pt rule to be cut and lipped with minimum effort.  
  • Waste pieces clear through the back of the female tool.
  • Lips and cuts any height of rule up to 30mm high and any length down to 2mm.     
  • Quickly adjustable, to lip 2pt or 3pt centre or side bevel.     
  • Creates distortion free lips for greater strength.    
  • A side gauge fitted for repetition work.      
  • Designed to produce left and right lips in one operation.     
  • Will lip one end only if required.
NOVA NOTCHER-click to enlarge
click to enlarge zoom

NOVA NOTCHER

Unique hand adjustment for comfort and maximum efficiency. Large mechanical advantage enables steel rule up to 6 pt creasing to be notched with minimum effort.  
  • Pre-bent and curved rule can be notched without obstruction.
  • Straight rules are held square by a support guide.      
  • Depth of notch adjustable up to 19mm.      
  • Standard notch 6mm or 10mm width.    
  • Alternative size tools can be supplied.      
  • Accurately ground tools ensure free notches without distortion.     
  • Side gauge fitted for repetition work.

BACK TO TOP









Show contact details





" ... Our motto is service.
If we don’t have the product in stock we will make it or order it in the
shortest possible time.”